How Do You Spool A Baitcaster Reel?

Should you wet fishing line before spooling?

warm water Always prior to spooling up with mono, leave your line submerged in a bucket of warm water This will allow the water to soak into the line helping not only when you come to wind the line on but also allowing the line to bed down property on your spool.

How long should you soak line before spooling?

At least for a few hours but ideally overnight The line will darken right up as it absorbs the water.” 2 “The reason for doing this is to make the mono go incredibly limp just like braid.

What are the holes in a Baitcaster spool for?

On a baitcaster, this can honestly be the hardest part on a baitcaster. If your reel has holes in the spool, you can thread the line through the holes and give the handle a quick twist to get the line all the way around spool If you don’t have holes, you’ll need to work at it to get the line around it completely.

Do I need to soak my braid before spooling?

Braid does not need soaking like you do with mono prior to spooling up Thread your braid through the eye on the but section of the rod. Double check that your spool is as far forward as possible. Tie a slip loop knot in your braid.

Which way should line come off spool?

Observe the direction the bail arm turns. If it turns in a clockwise direction it places line on the spool in a clockwise direction. So it is very important to have line coming off the filler spool onto your reel in a clockwise direction.

How much braid do you put on a reel?

When the line is about 1/16″ away from the top of the reel , you know you’ve put enough braid on. If you put too little braid on, you’ll inhibit your casting distance, and if you put too much on, you could be more susceptible to wind knots.

Do you need backing on a baitcaster?

You can tie monofilament or fluorocarbon directly to the spool and start filling the reel, but braided line slips too much when tied directly to the spool so you will need some type of backing to prevent this slippage.

What is it called when you pull line off your spool and it stays curled up?

Fishing line memory is what happens when monofilament line sits on a spool. It develops curls, which can reduce casting distance and increase the chances for snarls or tangles. It is nearly impossible to eliminate line memory completely.

Why does my line catch when I cast?

As mentioned before, if your line slows down quickly on a cast, those coils coming off the spool will catch up to each other and tangle up By simply pointing your rod tip straight out after you cast and before your lure hits the water, you are helping to reduce the friction of the line on the guides of the rod.

Why do bass pros use Baitcasters?

For using “power techniques”, working with heavier lures like crankbaits and ½ oz. spinnerbaits, or fishing in heavy weeds where you need strong line, Nels recommends baitcasters because they have more torque and handle heavy line better.

Why is Baitcaster better than spinning?

Baitcast reels can handle heavier line and actually allow for longer casts than spinning gear in the same size range Bass anglers regularly use line in the 14- to 17-pound-test range. Muskie and catfish anglers use even heavier line.

How much braid do you need on a baitcaster?

Thin diameter line is great for spinning reels, but if you’re using baitcasting reels, you don’t want to use anything under 20 lb. braid If the line is really thin, it’ll dig into the spool if you have a big fish on or get snagged, which can cause knots and tangles.

How much line should be on a baitcaster?

Casting reels should be between an eighth of an inch from the top and all the way to the top If you get too much line on them, you’ll get a weird sound when you cast. Spinning reels should be all the way full, right to the top. If you get too much line on them, the line will jump off the spool in coils.

Why does my line keep twisting?

If the line seems to tangle up, twist, or form loops, you’re spooling the line at 180 degrees from its natural bend and must turn the spool over (maybe wait on the nail until this step). If it doesn’t seem to form any loops more noticeable than its natural bend, you’re all set and keep spooling.

Where do you place the spool of thread?

The spool sits right on the spool pin , and gravity does the rest. The thread end goes through the guides on the stand, and you are ready to thread the machine. The proper placement of the thread stand is near the end of your machine. You can place it close to the right side, or to the back.

What does the brake do on a baitcaster?

The braking system on a baitcasting reel is designed to regulate the spool’s rotation during your cast , similar to how the brakes in your car work against your tires. “If you add more brakes to your reel when you cast, it’s going to provide a little bit more resistance on that spool,” Conlon says.

Can you use braided line on a baitcaster?

Braided line is often regarded as the best line for baitcaster fishing , but you still have to pick the right type of braid. Braided fishing line is made from several single strands of high molecular weight polyethylene that are then weaved together and is what gives braided line its incredible strength.

What is the dial on the left side of a baitcaster?

Magnetic brake systems use moving metal magnets and electromagnetic forces to slow the spool speed down. This system is usually controlled by a dial on the side of the reel that is tightened or loosened during the cast.

Do you put mono on before braid?

If you use normal monofilament, you can just fill your reel right up with it, but if you use braid, you need to put a base layer of monofilament on the reel beforehand This is called mono backing, and it could save you from losing the biggest fish of your life.

Citations

https://www.youtube.com/watch?v=QeDWlYISSwM
https://www.lews.com/en/learn/tips/how-to-spool-a-baitcast-reel

You May Also Like