Is it better to mount transducer on trolling motor or transom?
Mounting transducer on trolling motor vs transom Ideally, the transducer should be as close as possible to that position. So if you fish mostly off the back of the boat, a transom mount is best, but if you fish mostly off the front of the boat, it’s better to put the transducer on a bow mount trolling motor.
How far in the water does a transducer need to be?
The transducer should be even with the bottom of the boat or slightly below the bottom Leading edge (the edge closest to the transom of the boat). One click too high: the transducer is tilted out of the water and cannot maintain a sonar signal.
Can I mount a transducer inside the hull?
The most important thing to keep in mind is that transducers can only be glued inside hulls that are solid fiberglass or up to 1/8th” aluminum However, since boat hulls absorb acoustic energy, transmitting through the hull reduces the transducers performance.
Where do you mount a fish finder?
The general rule of thumb is to mount the transducer to the starboard side , which is the down stroke of most single outboard boat propellers (right hand lower unit). This side produces the least amount of turbulence and is most efficient in delivering the best performance.
Can you put 2 transducers on a trolling motor?
You can put one on each side of the transom I have 2 on one side and one on the other side. Use transducer mounting boards so you can adjust the location of the transducers and minimize the number of holes in the transom.
What way does a transducer face?
So the short answer is that no, it doesn’t matter which way you face the “front” of your transducer. the read out is going to look just the same to you. You do, however, want the BOTTOM of your transducer to face as straight down as you can, within reason.
Should transducer be flush with bottom of boat?
Ideally you’ll want the transducer about flush with the bottom or hull of your boat It could be too deep but it won’t hurt to try it. If you can’t get a bottom reading going wide open throttle you’ll want to adjust it.
Where is the best place to mount a transducer?
The location should be as close to the center of the boat as possible, but on the side of the downward swing the propeller On the majority of boats, this will be on the starboard (right) side.
Should transducer be submerged?
Note: the transducer must be submerged in water for reliable transducer detection If a transducer is detected, the unit will enter “Start Up” or normal operation unless you choose another option.
Can a transducer read through fiberglass hull?
As an alternative to transom mounting, it is possible on many fiberglass-hulled boats to glue the transducer on the inside of the boat hull Since fiberglass has similar sonar characteristics as water, the sonar signal can pass through the boat hull with minimal loss.
Can I install a transducer with the boat in the water?
When mounting the transducer, make sure that it is just under the water line, and parallel to the water surface If your cockpit is on the starboard side, it’s a good idea to mount the transducer on the same side, to make it easier to run a cable to the cockpit.
Can you install a depth finder while the boat is in the water?
No you cannot Only if you can remove the screws from the old one (if you can get them out) and put the new one in the exact same place, otherwise you’ll have hell getting the screws into fiberglass with a hand screwdriver.
How far below the boat should a transducer be?
Thirdly the best bet when mounting your transducer to read at speed is to have the bottom of it 3-4 mm below the waterline Because the transducer can only ping in water so you do want it submerged. If it’s too deep sometimes the front face of it will create turbulence and bubbles = bad.
What angle should my transducer be at?
The leading edge of the transducer should be even with the bottom of your boat The trailing edge of the transducer should be slightly lower than the leading edge.
What is a deeper chirp?
About this item. THE ONLY CASTABLE CHIRP FISH FINDER : The three-beam frequencies, crisp clarity, and extreme accuracy make it ideal for quickly locating target species holding spots, pinpointing predator fish, and fishing in extreme depths. HIGHEST SPECS: Casts out to 100m with solid connectivity.
Does side imaging work on a kayak?
Side-imaging works best when the kayak is moving Once I found structure or a fish mark, I could switch to down-imaging to investigate. Freeman suggested I adjust the filters on the signal. “Low noise will show less detail but also less interference,” he explains.
Do you really need a fish finder?
Are fish finders really necessary? Fish finders are not needed in order to locate and catch fish but they do provide highly valuable information like water temperature, water depth, bottom topography, the presence of fish, baitfish, as well as structure such as weeds, rocks, laydowns, and shelves.
How do you fill old transducer holes?
- Fill the holes with life caulk and allow to cure. Add an additional blob from the inside
- Get some flat headed #12 screws, countersink the holes slightly, and install them into the holes with Life Caulk.
- Drill the holes out larger and fill with an epoxy plug
- Order some quick cure 5200 and fill the holes.
Sources
https://www.youtube.com/watch?v=czVVDlKQROE
https://westerncanoekayak.com/magnetic-transducer-mount-15mm/
https://railblazausa.com/product/kayak-and-canoe-fishfinder-and-transducer-mounts/
https://www.youtube.com/watch?v=tAzy5mLXhBc
https://sportfishingbuddy.com/pros-and-cons-of-mounting-transducer-on-trolling-motor/